Voice & AI
Command feedback
Each voice command or grade is confirmed by taps and beeps: one for Again, two for Hard, three for Good, four for Easy.
What it does
Command feedback tells you that the app registered a command or a grade, without looking at the screen. It plays a short vibration and a short run of beeps. The four grades form a ladder: Again gives one tap and one beep, Hard two, Good three and Easy four. Reveal, Skip, Repeat and Stop use one or two taps and beeps at other pitches. In a hands-free session the same setting also plays a faint tick each second of a countdown and a longer tone when your turn to speak begins.
How to use it
- Open the Settings tab and find the Feedback section.
- Make sure Command feedback is on. It is on by default.
- Choose what you want: Vibration, Sound, or both. These two switches appear only while Command feedback is on.
- With Vibration on, set Vibration Strength with the slider. It runs from a weak setting at the left to full strength at the right.
- Start a hands-free classic session, as described in the speech recognition manual.
- Grade a card by saying Again, Hard, Good or Easy. You get one to four taps and beeps.
- Say Reveal, Skip, Repeat or Stop and you get one or two taps and beeps for that command.
- Listen during the countdowns: a faint tick marks each second, and a longer tone marks the start of your turn.
Settings that affect it
- Settings → Feedback → Command feedback — the master switch for vibration and sound. On by default.
- Settings → Feedback → Vibration — the taps. On by default.
- Settings → Feedback → Sound — the beeps, the countdown tick and the longer tone. On by default.
- Settings → Feedback → Vibration Strength — from 0.2 to 1.0 in steps of 0.1. Default 1.0, full strength. It is shown only while Vibration is on.
- Settings → Session → Speak grade aloud (again / good …) — a separate setting. After a grade the app says the grade word first, then plays the beeps. On by default.
Limits and honest caveats
- iOS can suppress vibration while the microphone is recording, so in a hands-free session you may hear the beeps and feel no taps. The beeps are the dependable signal. This comes from a note in the app’s code, not from a test on every phone.
- Besides the taps, the app triggers the phone’s standard vibration. Vibration Strength scales the taps only, not that vibration.
- The tick and the longer tone follow Command feedback and Sound. They have no switch of their own, and they play only in hands-free countdowns: the wait before the answer and the wait between cards. In a Voice exam they play during the wait for your answer.
- Command feedback plays in the classic session, including after a tap on a grade button and in Visual Review, and in the Focus session after a grade.
- The beeps are generated on the phone from simple tones. The feature uses no network.
- In a Voice exam grade words are ignored and there are no grade buttons, so the grade ladder never plays there. The other commands still play their taps and beeps.
FAQ
What do the taps and beeps mean?
Grades: Again is one, Hard two, Good three and Easy four. The taps are lightest for Again and heaviest for Easy. Reveal is one tap, Skip and Repeat are two, and Stop is one. The grade beeps share one pitch. Reveal is lower, Skip and Repeat are higher, and Stop is the lowest.
Why do I hear beeps but feel nothing?
iOS can suppress vibration while the microphone is recording, and hands-free sessions keep the microphone on. Check that Vibration is on and Vibration Strength is not at its lowest. If you still feel nothing, rely on the beeps.
What are the tick and the longer tone?
In a hands-free session, a very faint tick plays every second of the wait before the answer and of the wait between cards. A longer tone plays when that wait begins, as a cue that it is your turn to speak.
Does tapping a grade button play it too?
Yes. A tap on a grade button goes through the same path as a spoken grade, so it plays the same taps and beeps. With Speak grade aloud (again / good …) on, the app also says the grade word.
Can I keep the tick but turn off the beeps?
No. Sound controls the beeps, the tick and the longer tone together. You can keep Vibration on and turn Sound off, which silences all three.